Impulse changeover switch Flush mount Eltako EGS61Z-230V 2 makers 230 V 16 A 1 pc(s)
77,99 €
Product Description
Surge group switch for central control, 1 + 1 NO contact non-potential-free 10A/250V AC, for a 230V AC motor. Stand-by loss only 0.4 watts. For panel mounting. 45mm long, 45mm wide, 32mm deep. The latest hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. This surge group switch switches the commands of the sensor relays or switches and buttons and switches a 230V motor for a shading element or a roller shutter. Control-, Supply and switching voltage 230V A1, A7 and A8 must be controlled with the same potential as L. By using bistable relays, there is no coil power loss or heating thereby even when the relay is switched on. After installation, wait for the autoÂmatische short synchronization before connecting the switched consumer to the mains. The control input A1 is used to control pulses 'up, stop, off, stop' with a universal pushbutton. From the production week 25/18 a direction button for 'off' can be connected via the diode RTD (polarity does not matter). Another direction button for 'up' is connected directly to A1. On 1. Control pulse 'off', the EGS61Z switches control input A1 to 'direction button'. In order to switch control input A1 back to 'universal button', the supply voltage must be briefly switched off. The additional control inputs A7 and A8 are centrally controlled up and down with priority. With priority because these control inputs cannot be overmodulated by other control inputs as long as the central control contact is closed. A control signal activates the up or down switch position. Another control signal (less than 700ms) at this control input interrupts the sequence immediately, another control signal (greater than 700ms) continues the current action. Use the RV rotary switch to set the off-delay. If the surge group switch is in the 'up' or 'off' position, the set delay time runs, at the end of which the device automatically switches to 'stop'. The delay time must therefore be selected at least as long as the shading element or the roller shutter is required to move from one end position to the other. The WA rotary switch is used to control the automatic reversing mechanism: In the setting between 0.5 and 2 seconds the automatic turning is switched on. In this case, only when the delay time set with the upper rotary switch has elapsed is a reversal of the direction of rotation to e.g. tighten awnings or set blinds to a certain position. AUTO 1: No automatic turning and no comfort turning function. A7 and A8 actuation less than 1s = static sequence (contact closes only during operation) actuation greater than 1s = dynamic sequence (contact remains closed), stop with new actuation. AUTO 2: Turning mechanism with 1s turning time. In addition, the local comfort turning function for blinds is active at A1: A double pulse causes the slow rotation in the opposite direction, which is stopped with another pulse.This text is machine translated.
Impulse changeover switch Flush mount Eltako EGS61Z-230V 2 makers 230 V 16 A 1 pc(s)
Surge group switch for central control, 1 + 1 NO contact non-potential-free 10A/250V AC, for a 230V AC motor. Stand-by loss only 0.4 watts. For panel mounting. 45mm long, 45mm wide, 32mm deep. The latest hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. This surge group switch switches the commands of the sensor relays or switches and buttons and switches a 230V motor for a shading element or a roller shutter. Control-, Supply and switching voltage 230V A1, A7 and A8 must be controlled with the same potential as L. By using bistable relays, there is no coil power loss or heating thereby even when the relay is switched on. After installation, wait for the autoÂmatische short synchronization before connecting the switched consumer to the mains. The control input A1 is used to control pulses 'up, stop, off, stop' with a universal pushbutton. From the production week 25/18 a direction button for 'off' can be connected via the diode RTD (polarity does not matter). Another direction button for 'up' is connected directly to A1. On 1. Control pulse 'off', the EGS61Z switches control input A1 to 'direction button'. In order to switch control input A1 back to 'universal button', the supply voltage must be briefly switched off. The additional control inputs A7 and A8 are centrally controlled up and down with priority. With priority because these control inputs cannot be overmodulated by other control inputs as long as the central control contact is closed. A control signal activates the up or down switch position. Another control signal (less than 700ms) at this control input interrupts the sequence immediately, another control signal (greater than 700ms) continues the current action. Use the RV rotary switch to set the off-delay. If the surge group switch is in the 'up' or 'off' position, the set delay time runs, at the end of which the device automatically switches to 'stop'. The delay time must therefore be selected at least as long as the shading element or the roller shutter is required to move from one end position to the other. The WA rotary switch is used to control the automatic reversing mechanism: In the setting between 0.5 and 2 seconds the automatic turning is switched on. In this case, only when the delay time set with the upper rotary switch has elapsed is a reversal of the direction of rotation to e.g. tighten awnings or set blinds to a certain position. AUTO 1: No automatic turning and no comfort turning function. A7 and A8 actuation less than 1s = static sequence (contact closes only during operation) actuation greater than 1s = dynamic sequence (contact remains closed), stop with new actuation. AUTO 2: Turning mechanism with 1s turning time. In addition, the local comfort turning function for blinds is active at A1: A double pulse causes the slow rotation in the opposite direction, which is stopped with another pulse.This text is machine translated.
Related Products
59,99 €
Conrad Electronic International
42,99 €
Conrad Electronic International
63,99 €
Conrad Electronic International
63,99 €
Conrad Electronic International
42,99 €
Conrad Electronic International
63,99 €
Conrad Electronic International
81,99 €
Conrad Electronic International
73,99 €
Conrad Electronic International
65,99 €
Conrad Electronic International
Delivery, Returns & Refunds
Delivery
Sellers offer a range of delivery options, so you can choose the one that’s most convenient for you. Many sellers offer free delivery. You can always find the postage cost and estimated delivery date in a seller’s listing. You'll then be able to see a full list of delivery options during checkout. These can include: Express delivery, Standard delivery, Economy delivery, Click & Collect, Free local collection from seller.
Returns
Your options for returning an item vary depending on what you want to return, why you want to return it, and the seller's return policy. If the item is damaged or doesn't match the listing description, you can return it even if the seller's returns policy says they don't accept returns. If you've changed your mind and no longer want an item, you can still request a return, but the seller doesn't have to accept it. If the buyer changes their mind about a purchase and wants to return an item, they may need to pay return postage costs, depending on the seller's return policy. Sellers can provide a return postage address and additional return postage information for the buyer. Sellers pay for return postage if there's a problem with the item. For example, if the item doesn't match the listing description, is damaged or defective or is counterfeit. By law, customers in the European Union also have the right to cancel the purchase of an item within 14 days beginning from the day you receive, or a third party indicated by you (other than the carrier) receives, the last good ordered by you (if delivered separately). This applies to all products except for digital items (e.g. Digital Music) that are provided immediately to you with your acknowledgement, and other items such as video, DVD, audio, video games, Sex and Sensuality products and software products where the item has been unsealed.
Refunds
Sellers have to offer a refund for certain items only if they are faulty, such as: Personalised items and custom-made items, Perishable items, Newspapers and magazines, Unwrapped CDs DVDs and computer software. If you used your PayPal balance or bank account to fund the original payment, the refunded money will go back to your PayPal account balance. If you used a credit or debit card to fund the original payment, the refunded money will go back to your card. The seller will effect the refund within three working days but it may take up to 30 days for Paypal to process the transfer. For payments funded partially by a card and partially by your balance/bank, the money taken from your card will go back to your card and the remainder will return to your PayPal balance.