Product Description
Radio-outdoor motion-brightness sensor, 84x84x39mm. With solar cell. Smart home sensor The factory setting for the energy storage devices is empty and therefore, first recharge them in bright daylight for approx. 10 hours. At normal ambient brightness (at least 200 lux in the average day), the energy from the integrated solar module is sufficient to supply the sensor. The power reserve stored in capacitors supplies the power for the night. The sensor does not need any installation depth behind the retaining plate and can be screwed on any level surface. The complete module can be pulled from the frame for mounting. We recommend using stainless steel counter-sunk screws 2.9x25mm, DIN 7982 C. Both with 5x25mm plugs as well as on 55mm switch boxes. 2 stainless steel countersunk screws 2.9x25mm and 5x25mm plugs are included in the delivery. To teach in an actuator in the learning mode, the enclosed blue magnet or any other available magnet is held below the position of the sensor marked with a square to the side wall. In this way, a learning telegram is sent. The sensor measures from 0 to 2000 lux and transmits a message to the Eltako building radio every 100 seconds with a brightness change of at least 10 lux. A motion detection is sent immediately 2 times. The switch-off message is issued after the release delay that has been set fixed with 1 minute. If there is no change, a status message is sent approx. every 20 minutes. When teaching in actuators the switching threshold is determined, at which the lighting switches on or off depending on the brightness. If a FABH motion is reported, then the system is switched on. Only when all FABH programmed into an actuator do not signal any movement for one minute, the release delay of the actuator may start. Caution! For wall mounting, the FABH65S must be mounted with the holes facing down. The radio sensor can be programmed in the following actuators and in the building radio visualization and control software: F4HK14, FGM, FHK14, FHK61, FLC61, FSG14, FSG71, FSR14, FSR61, FSR71, FTN14, FTN61, FD14, FUD61, FUD71, FZK14, FZK61.This text is machine translated.
FABH65S-wg Eltako Motion detector Surface-mount
Radio-outdoor motion-brightness sensor, 84x84x39mm. With solar cell. Smart home sensor The factory setting for the energy storage devices is empty and therefore, first recharge them in bright daylight for approx. 10 hours. At normal ambient brightness (at least 200 lux in the average day), the energy from the integrated solar module is sufficient to supply the sensor. The power reserve stored in capacitors supplies the power for the night. The sensor does not need any installation depth behind the retaining plate and can be screwed on any level surface. The complete module can be pulled from the frame for mounting. We recommend using stainless steel counter-sunk screws 2.9x25mm, DIN 7982 C. Both with 5x25mm plugs as well as on 55mm switch boxes. 2 stainless steel countersunk screws 2.9x25mm and 5x25mm plugs are included in the delivery. To teach in an actuator in the learning mode, the enclosed blue magnet or any other available magnet is held below the position of the sensor marked with a square to the side wall. In this way, a learning telegram is sent. The sensor measures from 0 to 2000 lux and transmits a message to the Eltako building radio every 100 seconds with a brightness change of at least 10 lux. A motion detection is sent immediately 2 times. The switch-off message is issued after the release delay that has been set fixed with 1 minute. If there is no change, a status message is sent approx. every 20 minutes. When teaching in actuators the switching threshold is determined, at which the lighting switches on or off depending on the brightness. If a FABH motion is reported, then the system is switched on. Only when all FABH programmed into an actuator do not signal any movement for one minute, the release delay of the actuator may start. Caution! For wall mounting, the FABH65S must be mounted with the holes facing down. The radio sensor can be programmed in the following actuators and in the building radio visualization and control software: F4HK14, FGM, FHK14, FHK61, FLC61, FSG14, FSG71, FSR14, FSR61, FSR71, FTN14, FTN61, FD14, FUD61, FUD71, FZK14, FZK61.This text is machine translated.
Related Products
109,99 €
Conrad Electronic International
65,99 €
Conrad Electronic International
39,99 €
Conrad Electronic International
42,99 €
Conrad Electronic International
59,99 €
Conrad Electronic International
83,99 €
Conrad Electronic International
23,99 €
Conrad Electronic International
51,99 €
61,99 €
Conrad Electronic International
48,99 €
Conrad Electronic International
59,99 €
Conrad Electronic International
Delivery, Returns & Refunds
Delivery
Sellers offer a range of delivery options, so you can choose the one that’s most convenient for you. Many sellers offer free delivery. You can always find the postage cost and estimated delivery date in a seller’s listing. You'll then be able to see a full list of delivery options during checkout. These can include: Express delivery, Standard delivery, Economy delivery, Click & Collect, Free local collection from seller.
Returns
Your options for returning an item vary depending on what you want to return, why you want to return it, and the seller's return policy. If the item is damaged or doesn't match the listing description, you can return it even if the seller's returns policy says they don't accept returns. If you've changed your mind and no longer want an item, you can still request a return, but the seller doesn't have to accept it. If the buyer changes their mind about a purchase and wants to return an item, they may need to pay return postage costs, depending on the seller's return policy. Sellers can provide a return postage address and additional return postage information for the buyer. Sellers pay for return postage if there's a problem with the item. For example, if the item doesn't match the listing description, is damaged or defective or is counterfeit. By law, customers in the European Union also have the right to cancel the purchase of an item within 14 days beginning from the day you receive, or a third party indicated by you (other than the carrier) receives, the last good ordered by you (if delivered separately). This applies to all products except for digital items (e.g. Digital Music) that are provided immediately to you with your acknowledgement, and other items such as video, DVD, audio, video games, Sex and Sensuality products and software products where the item has been unsealed.
Refunds
Sellers have to offer a refund for certain items only if they are faulty, such as: Personalised items and custom-made items, Perishable items, Newspapers and magazines, Unwrapped CDs DVDs and computer software. If you used your PayPal balance or bank account to fund the original payment, the refunded money will go back to your PayPal account balance. If you used a credit or debit card to fund the original payment, the refunded money will go back to your card. The seller will effect the refund within three working days but it may take up to 30 days for Paypal to process the transfer. For payments funded partially by a card and partially by your balance/bank, the money taken from your card will go back to your card and the remainder will return to your PayPal balance.